Skip to content

How to open PS4

Rate this post

How to open PS4: Thanks to PlayStation 4 you have spent a lot of time playing your favorite video games, having fun with your friends and completing tons of challenges. However, electronic devices also need maintenance over the years. This can result from an accumulation of dust, or from a defective component that needs to be replaced. If you heard strange noises while playing on the PS4, or saw that there is a lot of dust in the vents, don’t be frightened!

This type of situation is completely normal, especially if a device, such as a console, is used for a long time. In case you need to take a look inside the PS4, know that you’ve come to the right place! Thanks to my advice, you will understand in a short time how to open the PS4 and verify its conditions without compromising its integrity.

How do you say? Can’t wait to get started? Then all you have to do is get comfortable and carefully read everything I’m about to tell you. You will see that opening the PS4 is a simpler operation than it seems. So I just have to wish you good reading and wish you a big good luck!

Preliminary information

Before we go ahead and show you how this is possible open a PS4I would like to give you some preliminary information in this regard.

As I mentioned earlier, with the passage of time even a PS4 needs maintenance, which can be useful in solving problems with dirt or technical failures. If, therefore, you feel that the console is overheating or that it produces suspicious noises, know that it is time to intervene.

What you need to know, however, is that by carrying out these operations, or by physically opening the console, unfortunately you will go to void its warranty. This means that, in the event of a breakdown, the console can no longer be taken over by Sony support, or by the retailer from which you purchased it. The only thing you can do about the console’s internal hardware without voiding the warranty is to change the hard drive.

If, despite this, you are still convinced to continue, be sure to implement all preliminary operations necessary to do a good job. Before opening the PS4 first make sure the console is off and therefore it is not simply in rest mode: if you have any doubts, or do not know how to perform this check, read my article where I explain how to turn off the PS4. Then make sure to unplug the power cord and HDMI cable connected to the TV.

Also, to open the PS4 you need to know that you will need the right equipment: a T8 screwdriver or T9 it’s a Phillips screwdriver with 3 mm tip.

 

Lindy 43012 Precision Torx Screwdriver Set, 5 pieces – T6, T7, T8 …

See offer on Amazon

 

The last thing left for you to do before opening the console is to place the PS4 on a plane dry And clean, in order to operate in the best conditions. I advise you to use a microfiber cloth. Having made these necessary premises, I would say that the time has come to continue and understand how to open the PS4.

How to open PS4 Fat

PS4 shell

If you have a PS4 Fatthat is a PlayStation 4 first model, here’s how you need to proceed.

The first thing to do, after taking care of disconnect the PS4 from each cable as I told you earlier, is to remove the body covering the hard disk, pushing it and then sliding it outwards. If you want to extract thehard disk from its slot, remove the lives placed at the bottom left. Next, turn the PS4 over and locate the i four rectangular stickers located on the back of the console.

Then remove the stickers possibly helping you with a cutter (I remind you that removing the four stickers will permanently invalidate the warranty). Once this is done, remove the screws you just discovered by helping yourself with the T8 / T9 screwdriverthen remove the body applying a little force and sliding it gently.

PS4 stickers

At this point, flip the PS4 again to remove the last one body remained. Then extract the two screws with a T8 / T9 screwdriver and, applying a little force, raise the body and then slide it. Now, by flipping the console over, you will have access to the fan (of which you can check theintegrity and the cleaning) and topower supply. To remove the latter, you need to extract in total five screws: two classic crosses placed at the corners, and others three to be removed with the T8 / T9 screwdriver placed at the edges.

Proceed, therefore, with the removal of the screws (taking care not to lose them) and extract, applying a little force, thepower supply. In this regard, I invite you to pay attention to the connectorpresent on your right, which you can disconnect (with the help of pliers) as soon as you have removed the power supply.

PS4 components

Once the power supply is removed, you will need to take care of the Blu-Ray player of the console. I warn you that this is a very operation delicateas a damage to the optical reader could compromise the correct one operation of the PS4. If you need a visual reference, I recommend viewing a YouTube video made by TronicsFix (in English, but very simple for everyone to follow) concerning just the procedure for disassemble the player.

So what you need to do is unplug the two Molex cablesfirst the color one black (the largest so to speak) and then the color one blue. The extraction of the two cables must be done extremely delicatedisconnecting them with small movements and avoiding abrupt maneuvers. Subsequently, with the help of a plierunplug the cable placed below the first Molex type you disconnected (the one with color black). Now all you have to do is remove the four screws placed in the corners of the reader, by providing the T8 / T9 screwdriver.

I advise you to do pay attention to the screw located in the lower right corner of the readeras it helps to keep the Wi-Fi moduleconnected with the thin black cable passing over the Blu-Ray player. Once the screw has been removed, in fact, you will have to move the cable with the module, removing it from above the reader.

Then proceed with removing the other screws placed at the corners and, finally, the last screw positioned on the bottom edge. Once these operations have been completed, you can finally remove the reader from its housing.

Now, if your intention, in addition to checking the health of the console components, is to clean the PS4, follow the instructions I gave you in my tutorial on the subject.

For reassemble each single component, afterwards, you will simply have to carry out the same steps backwards, always taking care not to damage any component and to insert all the screws in the correct way. Once you have finished all the operations, when you have to connect the appropriate cables again, I suggest you also read my guide where I explain how to connect the PS4 to the TV, in case you have any doubts about it.

How to open PS4 Slim

Open PS4 Slim

If you have one at home PS4 Slim, I inform you that the procedure to be implemented to open this version of the Sony home console has some variations compared to that of the PS4 Fat. To have a visual reference and follow each step in detail, I recommend watching a video tutorial on YouTube, like that of TronicsFix (in English but very understandable even for those who do not “chew” the language in question).

In this case, the first thing you need to do is to flip the console and remove theadhesive covering the screw, to be extracted later with a T8 / T9 screwdriver. Then remove the plastic next to the adhesive covering the hard disk screw, pushing it outwards. Once this is done, you will need to remove the rear bodyapplying a little force on the edges (one at a time) and sliding it gently.

Once you have removed the case, you will notice the presence of a metal plate covering the motherboard, and the optical reader of the console. To gain access to the motherboard, you will need to disconnect the Wi-Fi cable using pliers, and then disconnect each cable connected to the motherboard, always paying attention not to make sudden maneuvers.

Next, flip the console over to remove the front body levering the edges again to lift it. As you have surely noticed, unlike the PS4 Fat, in this case you will not have to remove any screws as regards the shells, which must be removed completely by hand. Therefore, once the front body is also removed, you will find thepower supply, the fan and the optical reader.

PS4 Slim Components

In this case, I’ll point out that the link for the Wi-Fi module it is located above the power supply. You will have to take care, therefore, to be careful to remove the screws on the power supply and then the one placed on the small one metal plate. In fact, by removing the power supply, you will immediately find the Wi-Fi antenna on the motherboard and, if you want to remove it, you will have to use a plier.

To have access to the fan and al optical reader, you will have to remove the metal plate placed on top, extracting the necessary screws and lifting it, always being very careful. If you have any doubts or want some visual help, watch carefully the video I recommended and you will see that the operation will be even easier!

How to open PS4 Pro

Open PS4 Pro

If your interest is to open one PS4 Prothen I announce that the operation is quite similar to the one concerning the PS4 Slim. To remove the front cover, all you have to do is lift it in each of the two front corners (one at a time) applying a little force. In this way, I assure you that you remove the front body it will be child’s play and you will immediately have access topower supplyat the fan and al optical reader.

To remove the rear bodyturn the console over and remove the plastic covering the hard disk. Next, remove the two stickers that cover the screws on the back of the console, to be extracted later with a T8 / T9 screwdriver. Don’t forget to remove the screw on the top back as well. Once this is done, with a little force, remove the rear body by lifting it and sliding it.

Also in this case, to have a clearer idea of ​​what to do, I recommend the vision of a video tutorial on Youtube, like the one of TronicsFix (always in English) in which it is perfectly explained how to open a PS4 Pro.